Home
1995 z32 TT
1992 z32 TT
Accent Stripe
AIV Delete
Antenna
Badgeless Rear Panel
Battery Optima Red Top
Big Brakes
Boost Gauge
Boost Sensor Hose
Boost Jets
Brake Idiot Light
Brake Master Cylinder
Butterfly Throttle Body
Carbon Canister Delete
Carpet Hole Repair
Center Console Removal
Classified ad
Clutch MC and Bleed
Cone Air Filter Placement
Connectors Under Hood
Delete & Bypass
Downpipes
Dyno Runs
Earthing Kit
Engine Pull
Exhaust
EGR Delete
Front Fascia
Fuel Line Clamps
Funky Fuses
Gear Shift Knob
Hatch Lock Stuck
Hella Horns
Hood Squeak
Idle Air Adjustment
Injector Dremel
Injector Testing
Interior Hatch Trim Repair
Jacking Car
Manual Boost Controller
Molding Replacement
Nose Panel
Parking Brake
Plenum Pull
PRVR Removal and Bypass
Pressure Wash
Radiator Hard Pipe Leak
Radiator Howe
Rear Interior Trim
Robo's Rules of Z-Dom
Seat Removal
Shock Install
Spare Tire
Speedometer 180 mph
Stereo Installation
Taillights JDM
Temperature Gauge
Throttle Sticking
Toluene
Vacuum Lines
When TT.net Goes Down
1987 z31 T
2004 Tacoma
2011 Tacoma
1974 Mercedes 450 SL
12 Hours of Sebring
24 Hours of Le Mans
AACA 2004 Hershey
Garage Remodel
Misc Album Pics
Misc Linked Pics
Numidia Raceway
SIR
Watkins Glen
Interesting Links
For Sale
Contact & Feedback
Disclaimer
 
 


We are currently creating content for this section. In order to be able to keep up with our high standards of service, we need a little more time. Please stop by again. Thank you for your interest!

Ha!  This is probably the most spurious mod I have tried to do to my car, but I don't regret it for a second. There is an unwritten rule that a car's top end should not be able to bury the speedometer needle.  Since my stock speedo faceplate "only" went up to "160 mph," I decided to try and replace it with this. 



I purchased my speedo faceplate on eBay from a guy based in Great Britain.  Last time I checked, this item was NLA (no longer available).    

Here are the instructions that came with the faceplate: "You must first find out where the true zero point is for the needle.  Before removing the needle you should keep it under power with the the ignition switched on and carefully lever the needle over the rest pin.  If the needle immediately springs back to the zero point, then the zero is at the pin.  If it stays below the pin then the zero point must be marked before disassembly.  On reassembly you must not put the needle on until the unit is under power, switched on and then put it at the zero point found earlier.  At all times you must remember not to remove the cluster with the battery connected, even if the ignition is switched off.   A household fork is a good tool for gently easing the needle off."

Realize that just zeros the needle.  The speedometer still needed to be calibrated since "high noon" on my old faceplate was around 80 mph.  I looked at a couple of electronic calibration devices.  These are basically little black boxes that need to be spliced into  different wires behind the speedometer, and cost upwards of $100-$150.  Yikes! 

I do not ever plan to test the top end of my Z anywhere except perhaps the Bonneville Salt Flats.  Please note that if for some insane reason you find yourself going faster than 140 mph in a Z, if you hit the brakes you will most likely warp your stock rotors from the heat.  You should coast to under 140 mph before touching the brakes, assuming of course that you have the room to do so.  Replacing the rotors would be preferable to replacing the entire car, or your life.  




 
 
Top